Solide edge 15 toàn tập :

Código QR

Solide edge 15 toàn tập : Vẽ và gia công khuôn

Hiển thị phiên bản (1) khác

Na minha lista:

Detalhes bibliográficos
Autor principal:	Phạm, Quang Huy
Formato:	Livro
Idioma:	Undetermined
Publicado em:	Hà Nội Giao thông Vận tải 2005
Assuntos:	Molding ( founding )
Tags:	Adicionar Tag Sem tags, seja o primeiro a adicionar uma tag!

Thư viện lưu trữ:	Trung tâm Học liệu Trường Đại học Cần Thơ

Registos relacionados

Solid edge 15 toàn tập :
Por: Phạm, Quang Huy
Publicado em: (2005)

Tự học Pro/Engineer 2000i bằng hình ảnh vẽ và gia công khuôn
Por: Phạm Quang Huy
Publicado em: (2003)

Hỏi-đáp về đúc gang
Por: Đinh Ngọc Lựa
Publicado em: (1979)

Hỏi-đáp về đúc hợp kim màu
Por: Đinh Ngọc Lựa
Publicado em: (1984)

Kỹ thuật làm khuôn và rót
Por: Ludgfred
Publicado em: (1975)

Kỹ thuật đúc
Por: Phạm, Quang Lộc
Publicado em: (2000)

Thí nghiệm kỹ thuật đúc
Por: Nguyễn, Ngọc Hà
Publicado em: (2006)

Các phương pháp đúc đặc biệt
Por: Nguyễn, Hữu Dũng
Publicado em: (2006)

Các phương pháp đúc đặc biệt
Por: Nguyễn, Hữu Dũng
Publicado em: (2006)

Các phương pháp và công nghệ đúc đặc biệt
Por: Nguyễn, Ngọc Hà
Publicado em: (2006)

Công nghệ đúc phôi thép
Por: Ngô, Trí Phúc
Publicado em: (2006)

Lập trình gia công khuôn với MasterCAM 9.1 phân hệ Mill ( Phay ) và Pro/ENGINEER
Por: Mai, Thị Hải
Publicado em: (2006)

Bài tập thực hành MasterCAM :
Por: Trần, Tường Thụy
Publicado em: (2005)

Lập trình gia công khuôn nâng cao với Mastercam 10 & 12
Publicado em: (2008)

Lập trình gia công khuôn nâng cao với Mastercam 10 & 12
Publicado em: (2008)

Kỹ thuật đúc
Por: Cương Dung
Publicado em: (1982)

Foundry engineering
Publicado em: (1963)

Thiết kế khuôn cho sản phẩm nhựa
Publicado em: (1995)

Kỹ thuật đúc
Por: Đinh Ngọc Lựa
Publicado em: (1980)

Nghiên cứu sinh tổng hợp B-D-Glucosidase từ Aspergillus niger VL01
Por: Phan, Thị Thuý Giàu
Publicado em: (2012)

Solid edge 15 toàn tập :Vẽ và gia công khuôn
Por: Phạm Quang Huy biên soạn
Publicado em: (2005)

Vật liệu làm khuôn cắt
Por: Đinh, Quảng Năng
Publicado em: (2003)

Vật liệu làm khuôn cát
Por: Đinh, Quảng Năng
Publicado em: (2003)

Design of plastic moulds and dies
Por: Sors, Laszlo
Publicado em: (1989)

Casting Kaiser aluminum
Publicado em: (1956)

Typographic Design in the Digital Studio
Por: Amdur, David A.
Publicado em: (2007)

Water in buildings :
Por: Rose, William B.
Publicado em: (2005)

Mimi and Bear in the snow /
Por: Trasler, Janee,
Publicado em: (2014)

Designing plastic parts for assembly
Por: Tres, Paul A.
Publicado em: (2000)

Fabrication of integrated microelectrodes for electrochemical detection on electrophoresis microchip by electroless deposition and micromolding in capillary technique /

Vẽ 3D, lắp ráp và mô phỏng với SolidEdge 15 và SolidWorks 2004
Publicado em: (2005)

Typographic design in the digital studio :
Por: Amdur, David A.
Publicado em: (2007)

Typographic Design in the Digital Studio
Por: Amdur, David A.
Publicado em: (2007)

When to bee social : Interactions among environmental constraints, incentives, guarding, relatedness in a facultatively social carpenter bee /
Por: Dunn, Tyler.

Phân lập và tuyển chọn nấm Aspergillus sinh tổng hợp enzyme Naringinase :
Por: Lưu, Thị Mỹ Tiên
Publicado em: (2011)

Development of reverse transcription (RT)-PCR and real-time RT-PCR assays for rapid detection and quantification of viable yeasts and molds contaminating yogurts and pasteurized food products /

Vật liệu làm khuôn cát
Por: Đinh, Quảng Năng
Publicado em: (2003)

Phân lập, tuyển chọn nấm mốc Aspergillus sinh tổng hợp Enzyme Naringinase
Por: Phạm, Quang Trung
Publicado em: (2010)

The condition assessment of cast resin molded transformer windings using vertical analysis of thermal distribution /

Fabrication of a spectrophotometric absorbance flow cell using injection-molded plastic /
Por: Hulme, John P.